Free Cheat-test Samples and Demo Questions Download
Adobe exams Adobe
Apple exams Apple
Avaya exams Avaya
Check Point exams Check Point
Cisco exams Cisco
Citrix exams Citrix
CIW exams CIW
CompTIA exams CompTIA
CWNP exams CWNP
EC-Council exams EC-Council
EMC exams EMC
Exin exams Exin
Fortinet exams Fortinet
GIAC exams GIAC
Hitachi exams Hitachi
HP exams HP
IBM exams IBM
Isaca exams Isaca
ISC exams ISC
ISEB exams ISEB
Juniper exams Juniper
LPI exams LPI
McAfee exams McAfee
Microsoft exams Microsoft
Oracle exams Oracle
PMI exams PMI
Riverbed exams Riverbed
SNIA exams SAP
Sun exams SAS
Symantec exams Symantec
VMware exams VMware
All certification exams

HP HP0-Y28 Exam - Cheat-Test.com

Free HP0-Y28 Sample Questions:

Q: 1
You must configure an HP MSM AP to operate in autonomous mode. At default settings, how will an IP address be configured for the AP's Ethernet port? (Select two.)
A. The AP will receive an address by DHCP from the nearest MSM AP.
B. The AP will receive an address by DHCP from a server on the wired network.
C. The administrator must configure an IP address while connected to the AP's serial port.
D. The AP will use an address from the DHCP scope configured on its internal DHCP server.
E. The AP will default to an address of 192.168.1.1/24.
Answer: B,E

Q: 2
You must manually provision an HP ProCurve MSM422 AP for deployment in controlled mode.
The AP previously was discovered and managed by a different controller in a different WLAN.
What must be done before you can perform provisioning steps using the AP's GUI?
A. The AP must be reset to factory defaults.
B. The AP must be switched to autonomous mode.
C. The AP must be assigned a static IP address.
D. The AP must discover the Mobility Controller in its new location.
Answer: A

Q: 3
You are configuring Layer 3 roaming for an HP ProCurve mobility solution that includes three HP Mobility Controllers. Which configuration item on the controllers must be identical?
A. SSID names
B. VSC names
C. AP Group names
D. Public Access settings
Answer: A

Q: 4
When is it necessary to specify an egress VLAN for a non-access controlled VSC bound to an AP Group as part of an HP ProCurve mobility solution?
A. when APs in the group must forward traffic from different VSCs to different VLANs
B. when APs in the group are not in the same VLAN as the Mobility Controller
C. when APs in the group must perform NAT for VSC clients with static addresses
D. when APs in the group are connected to switch ports with different VLAN assignments
Answer: A

Q: 5
You are designing an HP mobility solution for a conference center that will offer wireless service to conference attendees. Which customer specification requires the Guest Management tool?
A. The wireless network must support VPNs for business travelers.
B. Reception desk personnel must be able to activate, edit, and suspend guest accounts.
C. IT administrators must be able to manage bandwidth usage by guests.
D. A guest VSC must be able to be created with limited access rights.
Answer: B

Q: 6
On an HP ProCurve MSM760 Controller, you must configure an ACL to prevent Guest users from accessing Employee servers. You begin by defining the ACCESS-LIST attribute as:
employee, DENY,all,172.16.0.0/16,all
You must now define a USE-ACCESS-LIST attribute to implement this ACL. Which value should be used for this attribute?
A. employee
B. DENY
C. guest VSC
D. 172.16.0.0/16
Answer: A

Q: 7
You are installing an HP MSM422 AP in a customer network with an existing HP mobility solution where all APs are controlled by an HP MSM710 Controller. When the controller discovers the AP, how will the AP's radios be configured?
A. The AP's radios will be disabled until you set radio parameters.
B. The AP will use its autonomous radio settings until it is added to an AP Group.
C. The AP will inherit the configuration specified for the VLAN configured on its Ethernet port.
D. The AP will inherit the configuration of the MSM's Default Group.
Answer: D


© 2014 Cheat-Test.com, All Rights Reserved