Free Cheat-test Samples and Demo Questions Download
Adobe exams Adobe
Apple exams Apple
Avaya exams Avaya
Check Point exams Check Point
Cisco exams Cisco
Citrix exams Citrix
CIW exams CIW
CompTIA exams CompTIA
CWNP exams CWNP
EC-Council exams EC-Council
EMC exams EMC
Exin exams Exin
Fortinet exams Fortinet
GIAC exams GIAC
Hitachi exams Hitachi
HP exams HP
IBM exams IBM
Isaca exams Isaca
ISC exams ISC
ISEB exams ISEB
Juniper exams Juniper
LPI exams LPI
McAfee exams McAfee
Microsoft exams Microsoft
Oracle exams Oracle
PMI exams PMI
Riverbed exams Riverbed
SNIA exams SAP
Sun exams SAS
Symantec exams Symantec
VMware exams VMware
All certification exams

H3C GB0-190 Exam - Cheat-Test.com

Free GB0-190 Sample Questions:

Q: 1
Which of the following statements are TRUE about port-based 802.1X on a port?
A. The access users attached to the port are authenticated separately
B. When the first user on the port gets offline, all other users on the port are rejected to use the network.
C. After a user gets offline, other users can still use the network normally
D. Once a user on the port passes authentication, all other users attached to the port can access the network without being authenticated
Answer: B, D

Q: 2
Three MSR routers RTA, TRB and RTC connect to a frame relay network via their respective Serial 1/0 interfaces. The frame relay network can provide sufficient PVCs. As a network engineer, you need to assign IP addresses for these frame relay interfaces. Which of the following statements are TRUE? (Choose one or more)
A. With routes configured correctly, you need only one IP subnet to make the three touters communicate with one another through the frame relay network
B. If none of the routers is allowed to relay frames, you must configure at least two IP subnets for the three routers to communicate with one another through the frame relay network.
C. If none of the routers is allowed to relay packets, you must configure at least three IP subnets for the three routers to communicate with one another through the frame relay network.
D. With routes configured correctly, you can make the three routers communicate with one another through the frame relay network without having to configure subinterfaces for them Answer: A, B, D

Q: 3
Two customer routers MSR-1 and MSR-2 are interconnected via their respective GigabitEthernet 0/0 interfaces, and RIP runs between the two routers. RIP on each router has learned routes correctly. Add the following configuration on MSR-1:
frewall enable
acl number 3000
rule 0 deny udp destination-port eq 520
rule 5 permit ip
Apply the ACL to the inbound direction of GigabitEthernet 0/0 on MSR-1. Which of the following statements are TRUE?
A. MSR-1 still has RIP routes to the peer
B. MSR-1 cannot learn RIP routes from the peer
C. MSR-2 still has the RIP routes to the peer
D. MSR-2 cannot learn RIP routes from the peer
Answer: B, C

Q: 4
PPP is enabled on the Serial 0/0 interfaces of two customer routers MSR-1 and MSR-2. The two routers are configured with RIP to learn routes from each other. The configuration on MSR-1 is as follows:
rip 1
network 0.0.0.0
import-route static
#
Ip route-static 0.0.0.0.0.0. Serial10/0
Which of the following statements are FALSE about the configuration?
A. RIP redistributes the default route configured manually to MSR-2
B. The rip 1 command indicates the current RIP version is 1
C. MSR-1 thus configured will not dynamically advertise default routes to the peer through RIP
D. MSR-1 thus configured can dynamically advertise default routes to the peer through RIP
Answer: A, B, C

Q: 5
A network is set up as follows:
HostA----ge0/0----MSR-1---S2/0--------S1/0----MSR-2-----GE0/0----HostB
MSR-1 and MSR-2 are connected through a dedicated line. Configure the following three staic routes on MSR-1:
ip route-static 10.1.1.0 255.255.255.0.3.3.3.1
ip route-static 10.1.1.0 255.255.255.0.3.3.3.2
ip route-static 10.1.1.0 255.255.255.0.3.3.3.3
Segment 10.1.1.0/24 is the LAN where HostB resides. Which of the following statements is TRUE?
A. Only the third route will be added into the routing table of MSR-1
B. The three route will be added into the routing table of MSR-1 as equal-cost routes
C. Only the first route will be added into the routing table of MSR-1
D. None of the above
Answer: D

Q: 6
A network is set up as shown in the diagram. All interfaces of the four routers are OSPFenabled, and are all in OSPF Area 23. All network segments can communicate with each other. The OSFP cost of each link interconnecting routers is as shown in the diagram. Which of the following statements are TRUE? (Choose one or more)
A. RTD and RTA maintain the same LSDB
B. According to the SPF algorithm, RTC calculates that RTC->RTA->RTB is the optimal path to network segment 192.168.2.0/24
C. Through SPF calculation, RTC finds that the route to 192.168.4.0/24 and the route to 192.168.2.0/24 have the same cost. RTC thus generates
D. RTC will have two OSPF neighbors
Answer: A, B

Q: 7
On an MSR route, you can use the ________command to display the current path of the flie system.
A. dir
B. pwd
C. path
D. current-path
Answer: B

Q: 8
PPP is enabled on the WAN link between two customer routers MSR-1 and MSR-2. MSR-1 works as the authenticator to authenticate MSR-2 with PAP authentication. Which of the following configurations is required on MSR-2?
A. [MSR-2-Serial0/0] ppp pap user user
B. [MSR-2-Serial0/0] ppp pap password simple password
C. [MSR-2] ppp pap local-user user passwork simple passwork
D. [MSR-2-Serial0/0] ppp pap ocal-user user passwork simple passwork
Answer: D

Q: 9
When you use the ping command on an MSR router, you can use the_______ parameter to set the source IP address of ICMP echo requests.
A. -s
B. –l
C. –a
D. –d
Answer: C


© 2014 Cheat-Test.com, All Rights Reserved