Free Cheat-test Samples and Demo Questions Download
Adobe exams Adobe
Apple exams Apple
Avaya exams Avaya
Check Point exams Check Point
Cisco exams Cisco
Citrix exams Citrix
CIW exams CIW
CompTIA exams CompTIA
EC-Council exams EC-Council
EMC exams EMC
Exin exams Exin
Fortinet exams Fortinet
Hitachi exams Hitachi
HP exams HP
IBM exams IBM
Isaca exams Isaca
ISC exams ISC
Juniper exams Juniper
LPI exams LPI
McAfee exams McAfee
Microsoft exams Microsoft
Oracle exams Oracle
PMI exams PMI
Riverbed exams Riverbed
SNIA exams SAP
Sun exams SAS
Symantec exams Symantec
VMware exams VMware
All certification exams

Apple 9L0-009 Exam -

Free 9L0-009 Sample Questions:

1. Which THREE of the following items are appropriate to use for ESD prevention? SELECT THREE
A. Metal work surface
B. CRT discharge tool
C. Grounded work mat
D. Wrist strap and cord
E. Wireless wrist strap
F. Static-shielding bags
Answer: C, D, F

2. You are preparing to service a MacBook. To reduce the risk of damage from ESD, you clear the area of plastic, vinyl, or foamed polystyrene, and have static-shielding storage bags available for ESD-sensitive components. While you are working you should also remember to ________________ and _______________. SELECT TWO
A. ground yourself and the equipment you are working on
B. always place ESD-sensitive components on metal surfaces
C. discharge the display to protect the other ESD -sensitive components
D. handle any ESD-sensitive components by the connectors, rather than by the edges
E.ask other technicians to avoid touching you when you are working on ESD -sensitive components
Answer: A, E

3. You are removing the main battery from a MacBook Pro (17-inch, Early 2009). Which of the following is a best practice when handling this battery.?
A. Handle the battery with one hand, pressing between the soft side and the hard side.
B. Re-cover any punctures or tears in the soft mylar covering with Kapton tape.
C. Handle the battery any way; it does not matter.
D. Hold the battery carefully by its edges only.
Answer: D

4. Which part or parts of a CRT display should NOT be touched until after the display is disconnected from its power source and the CRT is properly discharged? SELECT ALL THAT APPLY
A. Yoke assembly
B. Anode aperture
C. High voltage cable
D. Front of CRT display
E. Flyback transformer
F. Outer plastic housing
Answer: A, B, C, E

5. Which of the following is a valid precaution you should take when you begin working inside a MacBook Pro (13-inch, Mid 2010)?
A. Reset the SMC.
B. Remove the hard drive.
C. Disconnect the optical drive.
D. Disconnect the main battery.
Answer: D

6. Which safety issue applies to newer Apple portable models?
A. Fragile bottom case
B. High voltage display
C. Heavy internal frame
D. Soft battery enclosure
E. Sharp logic board edges
Answer: D

7. Which THREE of the following are valid CRT safety rules? SELECT THREE A. Touch the computer's metal chassis.
B. Wear a grounded ESD wrist strap.
C. Connect the AC power cord.
D. Remove any metal jewelry.
E. Wear safety goggles.
F. Don't work alone.
Answer: D, E, F

8. You are troubleshooting an iMac (Early 2008) that does not power on. You notice that all diagnostic LEDs remain off when a known-good power cord is connected to the iMac and to a known-good power outlet. What is most likely the cause of these symptoms?
A. Faulty power supply
B. Faulty optical drive
C. Faulty LCD panel
D. Faulty video card
Answer: A

9. A customer asks if there is a diagnostic that he can use to help troubleshoot a hardware problem with his MacBook Pro. Which of the following solutions should you suggest?
A. Apple Service Diagnostic
B. Apple Hardware Test
C. Terminal
D. Console
Answer: B

10. Apple Service Toolkit uses ____ to check Macs with Mac Resource Inspector and other diagnostic utilities.
A. NetBoot
B. Open Firmware
C. Target Disk Mode
D. Apple Remote Desktop
Answer: A

© 2014, All Rights Reserved